PONDTITE

Use for waterproofing fishponds, fountains, water features, non-potable water holding tanks, and reflecting pools.

PondTite is not intended for use in swimming pools or spas.

PLEASE READ AND FULLY UNDERSTAND ALL THE INSTRUCTIONS PRIOR TO USE. IF YOU ARE UNSURE ABOUT ANY PART OF THE APPLICATION PROCEDURE OR IF YOU REQUIRE ANY FURTHER INFORMATION CONTACT THAI BONDALL Mobile: 07.2773874 Office: 076.282403.

FEATURES AND BENEFITS:

• Easy to use 
• Water Based 
• Forms a Tough, Flexible, Seamless Membrane ?Resistant to Algal and Fungal attack 
• Non-Toxic to aquatic plants and fish 
• Environmentally friendly 
• Suitable for interior and exterior use 

Do not use Bondall PondTite directly onto steel, iron, aluminium, wood, plastic, glass or fibreglass surfaces as these require special primers and coatings. Substrates such as kiln fired glazed pots, uros etc previously sealed and/or waterproofed substrates or other substrates not mentioned may require special preparation and/or special coatings prior to treating with Bondall PondTite. 

COVERAGE RATE:
It is important to accurately measure the area to be coated to determine the correct quantity of Bondall PondTite is purchased to successfully complete the job. Insufficient material could result in failure.

To complete each square metre of surface area, you will need 1.5 litres of Bondall PondTite equally divided between two coats.

Eg: For a surface area of 4 square metres you will require 6 litres (4 x 1.5 = 6) of product equally divided between 2 coats i.e. 3 litres per coat.

SURFACE PREPARATION AND PRIMING:

NEW MASONRY SURFACES:
Masonry includes new concrete, sand/cement renders, concrete blocks, limestone, sandstone, bricks and fibre cement sheeting.
New concrete surfaces should be cured for at least 72 hours prior to being thoroughly cleaned to remove any laitance which may affect adhesion. Once cleaned, apply two coats of Bondall Epoxy Prep Surface Conditioner to the surface, accurately following the instructions and leave to cure overnight.
New masonry surfaces should be free from any “dags” and sharp edges (do not apply on exposed aggregate finishes). All stonework should be properly bedded in sand/cement mortar with the desirable inclusion of Bondcrete in the gauging water. The surface should be thoroughly cleaned and be free from dirt, dust, salts, grease, oil and any other contaminants.

EXISTING/MATURE MASONRY SURFACES:
Existing masonry surfaces should be thoroughly cleaned to remove any algal and fungal growth by using Bondall Moss and Mould Eliminator. Surfaces should be free from any “dags” and sharp edges (do not apply on exposed aggregate finishes). The surface should be thoroughly cleaned and be free from dirt, dust, salts, grease, oil and any other contaminants. Once cleaned, apply two coats of Bondall Epoxy Prep Surface Conditioner to the surface, accurately following the instructions and leave to cure overnight.
PREVIOUSLY COATED OR PAINTED SURFACES:
If the surface has been previously coated, the coating must be completely removed back to the original substrate. Once cleaned, apply two coats of Bondall Epoxy Prep Surface Conditioner to the surface, accurately following the instructions and leave to cure overnight.

All holes or cracks in the surface should be filled with a fine sand/cement/Bondcrete mortar (3:1) thoroughly worked into the area and allowed to cure. Prime the ENTIRE surface with Bondall Epoxy Prep Surface Conditioner and allow to dry. Install a bond breaking tape and Bondall Polyweave reinforcing fabric to all corner junctions and joints. A bond breaker is recommended to accommodate any substrate movement in corners and joints. Apply a bond breaking tape (such as 18mm vinyl electrical tape) to all corners and/or joints. Allow the tape to bridge the joint or corner with equal amounts on either side. Generously coat 75mm either side of the bond breaking tape with Bondall PondTite, and while still wet embed a strip of Bondall Polyweave reinforcing fabric into the wet membrane with a short bristle paintbrush. Ensure all bubbles are removed from beneath the reinforcing fabric. When this is dry, apply another coat over the taped and fabric reinforced area. Once this is dry, apply Bondall PondTite to the rest of the surface to be treated.

GENERAL APPLICATION:

• Prior to application ensure correct surface preparation has been carried out. 
• Stir contents slowly with a broad blade or paddle before use. 
• DO NOT SHAKE as this will cause aeration. 
• Allow at least overnight drying between coats, or longer if temperature is low or humidity is high 
• DO NOT APPLY IN CONDITIONS WHERE THE TEMPERATURE IS LIKELY TO FALL BELOW 10ºC WHILE THE COATING IS DRYING 
• DO NOT APPLY IF RAIN IS LIKELY THE DAY OF APPLICATION OR SOON AFTERWARDS. 
• Apply Bondall PondTite with a good quality medium to firm bristle brush 
• Apply a substantially thicker coating than paint. Ensure no bubbles are left in the membrane by laying off. Try to avoid excessive build-up in corners. 
• Apply second coat at right angles to first coat. 
• Due to the extra thickness of the material allow extra drying time if conditions are cold, damp or humid. 
• Use directly from the can as dilution is generally not necessary. If dilution is necessary to assist with application in warm conditions, do not reduce by more than 5% with clean water. 

Allow a minimum of 7 days drying or longer from the time of completion before continuous immersion in water.

FILLING FISH PONDS:
After a minimum of 7 days (or longer in cooler/humid conditions) clean and rinse the pond. Some preservatives used in the manufacture of Bondall PondTite need to be fully removed from the surface before introducing fish. Wash off these preservatives from the pond surface by sponging the surface with clean water mixed with a small amouot of dish washing liquid and thoroughly rinse the pond with fresh clean water ensuring no traces of detergent remains. Fill the pond with clean water and let this stand for 1-2 days. Empty this water and refill again with clean water.
As there are a number of factors that can impact on the livelihood of fish and plants we recommend obtaining information on conditioning the water prior to introducing fish and aquaculture from a reputable pet store, fish breeder, nursery or similar.

COLOURS AVAILABLE:
Pale blue, Limestone and Black.

GLOSS LEVEL:
Matt Finish

SIZES AVAILABLE:
1litre and 4litre containers.

CLEAN UP:
Clean all equipment promptly using a stiff bristle or wire brush and cold or warm soapy water. Follow up by a fresh water rinse and dry. Mineral turpentine can also be used to soften hardened material on tools etc.
Do not pour PondTite or PondTite washings down drains or sinks. Dispose of any waste materials according to local council regulations.

SAFETY:
Avoid contact with skin and eyes. Should contact occur to the eyes, flush with water for 15 minutes, and seek medical attention should irritation develop. If poisoning occurs contact a doctor .Do not induce vomiting. Give water to drink. We always suggest the wearing of suitable protective clothing including impervious gloves and eye protection during application and preparation.

DISCLAIMER:
The performance of this product is dependant upon its correct preparation, application onto sound surfaces and attention to the instructions on the label. The wide variety of surface conditions makes it impossible for the company to assume liability for any loss, consequential or otherwise, arising from the use of this product. Should the product be found defective our liability shall be limited to the replacement of the product only. We reserve the right to amend specification and application techniques without prior notice.